Building parts
Revolve: Spin a Sketch Around an Axis
Revolve in the True Robotics Design Playground spins closed sketch regions around an axis to make round parts like wheels, knobs, pulleys and cups. Press Revolve or Shift+V, pick the regions, click a line, an edge or an axis to spin around, set the angle and click the green check. A full 360 degrees makes a solid all the way around.
How do I revolve a sketch?#
Sketch half the shape On a plane the axis runs along, like Front, sketch the outline of one side of your part, from the center out. Then draw a construction line right where the axis goes, like the center line of a knob, and finish the sketch.
Start Revolve Click Revolve in the toolbar, right after Cut, or press Shift+V. The Revolve panel opens on the left with the regions of the sketch you just finished in Regions and faces. If the sketch has one construction line clear of those regions, it is already your axis.
Pick the axis No axis yet? Click the Axis box, then click the line to spin around: a sketch line, a straight edge of a part, the round wall of a hole, or an Axis you made. The X, Y and Z buttons under the box pick an origin axis in one click.
Set the angle Angle starts at 360 degrees, a full turn. Keep it, or type a smaller angle like
180, or click the up and down arrows next to the box. The purple preview turns with it.Finish Click the green check at the top of the panel, or press Enter. Revolve 1 joins the feature list, and its sketch tucks in under it.
Already picked something before you pressed Revolve? Regions or a flat face you picked start out in Regions and faces, and a line, an edge or an axis you picked starts out as the axis, so sometimes all that is left is the green check.
Tip: Draw half, get the whole thing
Revolve is the tool for anything round that is more than a plain cylinder. Draw the outline of one side, from the center line out, and Revolve spins it into the whole part. A pulley is a rectangle with a notch in its outer side, and a cup is an L shape.
What can I revolve?#
Closed regions of one sketch (a region with a hole in it works too), or one flat face of a part. Pick regions from a second sketch and the panel swaps in your new pick, since a revolve takes its profile from one place.
What can be the axis?#
- A line in a sketch, solid or construction. A line in the same sketch is the handiest choice, because it moves with the profile whenever you change the sketch. Clicking a sketch row in the feature list while the Axis box waits picks its one construction line, or its one line.
- A straight edge of a part, to spin a profile around a corner or along a side.
- A round face, like the inside of a hole or the outside of a shaft. Its middle becomes the axis.
- An Axis you made, like the line where two faces meet. Click its dashed line in the view or its row in the feature list.
- The X, Y or Z axis, with the buttons under the Axis box.
The axis has to lie flat in the plane of the profile, and the profile has to stay on one side of it. The profile can touch the axis, which makes a solid middle, or sit away from it, which leaves a hole down the center, like a ring or a washer.
How does the Angle box work?#
Angle is how far the profile turns, from just above 0 up to 360 degrees. At 360 the part goes all the way around and closes up on itself. Anything less leaves a slice, like half a wheel at 180 or a quarter at 90, with flat ends where the turn starts and stops. The arrows next to the box step 1 degree at a time (Shift for 10, Alt for a tenth), and the box reads math too, so 360/8 works.
| Choice | What it does | Use it for |
|---|---|---|
| One way (the default) | Turns from the profile by the angle you type. | Full turns, and most slices. |
| Flip | Turns the same angle the other way around the axis. | A slice that went to the wrong side. |
| Symmetric | Turns half the angle each way from the profile. | A slice centered on the sketch, like 90 degrees with 45 on each side. |
What do New, Add, Remove and Intersect do?#
The same four operations as Extrude. New makes a new part. Add joins the revolve to the parts it touches. Remove cuts it away, which is how you turn a groove around a shaft or a round pocket into a part, and its preview is red. Intersect keeps only the material where the revolve and your parts overlap.
How do I change a revolve later?#
- Double-click Revolve 1 in the feature list. The model rolls back to just before it, and the panel opens with your picks, so you can change the regions, the axis, the angle or the operation.
- Change the sketch, like the width of a wheel or the depth of a groove, and the revolve follows. Sketches on its flat ends and faces follow it too.
- Right-click the row (or use its three dots) to rename, suppress or delete it, like any feature.
Can I round, mirror or pattern a revolve?#
Yes. Fillet and chamfer work on the round edges where a flat end meets a round side, like the rim of a wheel. Mirror, Linear pattern and Circular pattern copy a revolve in Features mode, so one revolved peg can become a row of pegs, each one following every change to the first.
What do the revolve messages mean?#
| Message | What to do |
|---|---|
| Pick a region or a flat face to revolve. | Click a closed region of a sketch, a sketch row in the feature list, or a flat face. |
| Pick an axis to revolve around. | Click the Axis box, then a sketch line, a straight edge, a round face or an Axis, or click X, Y or Z. |
| The profile crosses the axis. Move it to one side of the axis, or pick another axis. | Part of the profile sits on each side of the axis. Move the axis to the edge of the profile, or change the sketch so it stays on one side. |
| The axis needs to lie on the profile's plane. Pick a line in the sketch, or an edge or axis that lies on that plane. | The axis points out of the sketch. A line in the same sketch always works. |
| A flat face has no axis. Pick a sketch line, a straight edge, a round face or an axis. | You clicked a flat face while the Axis box waited. Click one of its straight edges instead. |
| Give this revolve an angle more than 0 and up to 360 degrees. | Type an angle from just above 0 up to 360. |
| The axis this revolve turns around is gone. Edit the revolve and pick another axis. | The line or Axis it used was deleted. Double-click the revolve and pick a new axis. |
Revolve opens up wheels, pulleys, knobs, spacers and bottles. Pair it with an Axis to spin around a hole or an edge, and with Circular pattern to add spokes and bolt holes.
Questions and answers#
How do I make a wheel or a knob?
Sketch the outline of one side of it, from the center line out, then press Revolve, pick the center line as the axis and leave the angle at 360. The sketch spins all the way around into a solid round part.
Why does Revolve say the profile crosses the axis?
A revolve spins the profile around the axis, so the profile has to stay on one side of it. Move the axis to the edge of the profile, or change the sketch so nothing sits on the other side.
Can I revolve less than a full turn?
Yes. Type any angle from just above 0 up to 360. A half turn at 180 makes half a wheel with two flat ends, and Symmetric turns half the angle each way from the sketch.
Can Revolve cut a groove?
Yes. Set the operation to Remove, and the revolved shape is cut away from the parts it passes through, like a groove around a shaft or a pulley.