True Robotics Design Playground HelpHelpOpen the True Robotics Design PlaygroundOpen app

Building parts

Axis: Make a Line to Turn Around

An Axis in the True Robotics Design Playground is a straight reference line you place yourself, shown as a long dashed line with its name. Press Axis or Shift+X and make one along a sketch line or edge, through two points, where two planes or faces meet, or down the middle of a hole. Then Revolve, Circular pattern, Mirror, Linear pattern and Angle planes can use it.

  • Updated
  • 6 minute read

Why make an axis?#

The X, Y and Z axes all run through the origin, but the line you want to turn around often sits somewhere else: the middle of a hole off to the side, a hinge along the edge of a box, or the corner where two faces meet. An Axis puts a line exactly there. It stays tied to what you made it from, so when the part changes, the axis moves with it, and so does everything built around it.

How do I make an axis?#

  1. Start Axis Click Axis in the toolbar, right after Plane, or press Shift+X (X for an axis). The Axis panel opens on the left.

  2. Choose how to make it Pick a way at the top of the panel: Line, Points, Planes or Round. The note under the buttons says what that way does, and the hint at the bottom of the view says what to click.

  3. Click what it needs Click the line, the two points, the two planes or the round face in the view, or a plane or axis row in the feature list. A long dashed preview line with the axis name shows where it goes. Flip, under Direction, turns it around end for end, which sets the way a revolve turns and a pattern runs.

  4. Finish Click the green check at the top of the panel, or press Enter. Axis 1 joins the feature list, and its dashed line stays in the view with its name.

Already picked something before you pressed Axis? A round face starts the axis down its middle, and two planes or flat faces start it where they meet. Clicked a round face while Line is chosen? The panel switches to Round for you.

What are the ways to make an axis?#

Ways to make an axis
WayWhat to clickGreat for
LineA line in a sketch (construction lines too), a straight edge of a part, or another axis.A hinge along an edge, or an axis you drew exactly where you want it.
PointsTwo points: sketch points, corners of a part or the origin.A slanted axis from one corner to another.
PlanesTwo planes or flat faces that cross. The axis sits where they meet.The corner line between two faces, or the line where Front and Right cross.
RoundThe round wall of a hole, or the outside of a shaft or boss. The axis runs through its middle.Turning or patterning around a hole that is not on the origin.

What can use an axis?#

  • Revolve spins a sketch around it.
  • Circular pattern repeats features or parts around it.
  • Mirror turns a copy half a turn around it when you choose Line.
  • Linear pattern runs its row along it.
  • An Angle plane tilts around it, like a door on its hinge.

While one of those boxes waits for a line, click the dashed axis in the view or its row in the feature list.

How do I hide, edit or delete an axis?#

  • Click the eye on its row to hide it, and again to show it, just like a plane. A hidden axis still works for everything that uses it.
  • Double-click it to change the way it is made or what it is made from. Everything after it rebuilds when you click the green check.
  • Right-click the row (or use its three dots) to rename it, so Axis 1 can become Hinge or Wheel center.
  • Press Delete to delete it. If a feature uses it, the app asks first.

Tip: Axis or sketch line?

A line in a sketch works as an axis for most tools too. Make an Axis when the line belongs to the part, like the middle of a hole, so it follows the part, or when several features should turn around the same line.

What do the axis messages mean?#

Axis messages
MessageWhat to do
Pick a sketch line or a straight edge for this axis to run along.Click one straight line in a sketch, or a straight edge of a part.
That face is flat. Pick one of its straight edges instead, or a sketch line.A flat face is not a line. Click one of its edges.
Pick one more point. The axis runs through both.Click a second sketch point, part corner or the origin.
Those two points are in the same spot. Pick two points apart from each other.Click a point somewhere else for the second one.
Those two face the same way, so they never meet. Pick two that cross, like a top face and a side face.Parallel planes never meet. Pick two that cross.
That face is not round like a hole or a shaft. Pick a round face.Click the round wall of a hole, or the outside of a shaft or boss.
The line this axis runs along is gone. Edit the axis and pick another line or edge.Something the axis was made from was deleted. Double-click the axis and pick again.
This uses Axis 1, which is suppressed. Turn Axis 1 back on to bring this back.A revolve or pattern turns around an axis you suppressed. Turn the axis back on, or pick another one.

An axis is a small thing that makes big shapes easy. Try one with Revolve to spin a wheel around a hole, or with Circular pattern to ring a hole with bolts.

Questions and answers#

What is an axis in CAD?

An axis is a straight reference line that features can turn around or run along. It does not add any material. Revolve spins a sketch around it, and a circular pattern repeats copies around it.

How do I make an axis through the middle of a hole?

Press Axis, choose Round, click the round wall of the hole and click the green check. The axis runs straight down the middle of the hole and follows it if the hole moves.

Can I hide an axis?

Yes. Click the eye on its row in the feature list, just like a plane. A hidden axis still works for every feature that uses it.